The first impression was very positive! Even though it is “made in China” it looks very well designed and made. The build quality is on very high level. It is not plastic like Atik, but metallic. The original package comes with camera, T-2 to 1,25″ nosepiece adapter, USB cable and setup instructions. I have also ordered RJ-11 cable for direct autoguiding via camera.

I got impressed when I unscrewed the nosepiece because of the size of the CCD. It seems really huge comparing to tiny CCD detectors in webcams (Atik ATK-2HS also uses ordinary 640×480 one). The resolution is 1280 x 1024, more specification are available at the QHY website.

QHY5 without nosepiece

The best thing is that QHY5 has T-2 thread which perfectly fits to my autoguiding telescope so I can just screw it on.

QHY5 on the autoguiding telescope

As you can notice it has two ports in the back side. One is USB 2.0 port for connection with the computer and another is ST-4 compatible autoguiding port for direct connection with the mount. I am using Vixen SkySensor hand-controller and I though that it is compatible but in fact it isn’t, because Vixen uses it’s own standard for autoguding. The connector is the same but wires are connected differently so today I am going to make a new cable. The camera has also build-in red LED diode which is too bright and could be disturbing in a completely dark so I pasted a black stripe over it.

Back side of QHY5

The camera comes with one A4 paper sheet of instructions how to setup. The drivers are not included, you have to download it from the Modern Astronomy site. The setup is really simple, you just install the generic driver and plug in the camera. Then you have to install additional driver for the autoguiding software you are using, in my case Guidemaster. All the main autoguiding software are supported, including ASCOM platform.

To sum up, I am very satisfied with the purchase. Two days ago I had a first light and everything worked fine. I was planning to capture M102 but ended with just 2 pictures because it clouded. This is 100% crop of one of them as a proof that camera guides OK:

100% crop of M102

I hope you enjoyed the review. If you have any questions don’t hesitate to ask under the comments

On the beginning of summer 2008 I figured out that the situation from the point of light pollution from my backyard is so bad that I need the solution. On the web I found some filters that suppress the light pollution but no one good review of them.

In the end I decided for IDAS LPS filter of Hutec. Because I was pretty sure I will be using just for astrophotography I decided for front-filter (look at this figure) which can be placed directly in the camera’s body so I can use it with lenses also and not just with the telescope. The version of filter is P2, that means that is the most suitable for astrophotography in prime focus.

The filter arrived on June and costed approximately 250 eur here in Europe, in USA it’s a bit cheaper. The first impression was something like: “250 eur for such a piece of glass?!??”. But after a first-light I changed my opinion. It is worth every single pennie! It works just the best for me, my backyard turned to the very good astrophotography place. It has no affect to sharpness of the image. I use it with my Canon 350D (Baader mod.) and also both sample pictures are captured with this equipment. The telescope was William Optics SuperAPO 80/480 with TeleVue reducer/flattener 0.8x. The picture without filter is out of focus because when I removed the filter I didn’t refocused. Anyway, it represents the affect of filter. Both pictures are captured at the same settings: f/4.8, ISO1600, 120s, RAW, WB(2850, -30), imported and exported with Lightroom.

The image without Hutech IDAS LPS filter

The image with Hutech IDAS LPS filter

It’s quite obvius what the filter does.

I have also measured the Mean of these two pictures. The median value for the picture without IDAS LPS is 118 whereas the median for picture with IDAS LPS filter is 52.

That’s all, hope that this article will help someone to decide what to buy or not to buy.